Setup a simple wireless link

Yaser Rahmati | یاسر رحمتی

Setting up a simple wireless link between two MikroTik devices involves configuring one device as an Access Point (AP) and the other as a Station (Client). This setup is commonly used to extend network coverage or connect two different network segments wirelessly.

Here’s a step-by-step guide:

1. Hardware and Initial Setup

Requirements:

  • Two MikroTik devices with wireless capabilities.

  • Basic knowledge of MikroTik RouterOS.

  • Winbox or SSH access to both MikroTik devices.

2. Configuring the Access Point (AP)

Step 1: Access the AP Device

  1. Connect to the MikroTik device using Winbox, WebFig, or SSH.

  2. Open the Wireless settings by navigating to Wireless in the left menu.

Step 2: Set Up the Wireless Interface

  1. Enable the Wireless Interface:

    • Go to the Interfaces tab in the Wireless window.

    • Double-click on the wireless interface (usually named wlan1).

    • Check the Enable box.

  2. Configure the Wireless Mode:

    • Under the Wireless tab, set the Mode to ap-bridge.

    • Set the SSID (Service Set Identifier) to a unique name (e.g., MikroTik-AP).

    • Set the Band to the desired frequency (e.g., 2GHz-B/G/N or 5GHz-A/N).

    • Set the Channel Width to 20MHz or 20/40MHz (depending on your bandwidth needs).

    • Choose a Frequency (e.g., 2412 for 2.4GHz or 5180 for 5GHz).

    • Leave other settings as default for simplicity.

  3. Security Profile:

    • Go to the Security Profiles tab.

    • Click + to add a new security profile.

    • Set the Name to something descriptive (e.g., Secure-AP).

    • Set WPA2 PSK as the Authentication Type.

    • Enter a strong WPA2 Pre-Shared Key (e.g., MySecurePassword).

    • Click Apply and OK.

  4. Assign the Security Profile to the Wireless Interface:

    • Return to the Wireless tab of the wlan1 interface.

    • Select the Security Profile you just created from the dropdown menu.

    • Click Apply and OK.

Step 3: Set Up IP Addressing

  1. Assign an IP Address to the Bridge Interface:

    • If you're using a bridge, go to Bridge -> Bridge tab and create a new bridge (e.g., bridge1).

    • Go to IP -> Addresses and assign an IP address to the bridge interface (e.g., 192.168.1.1/24).

    • Link the wireless interface wlan1 to the bridge under the Ports tab in the Bridge section.

  2. DHCP Server (Optional):

    • If the AP is providing IP addresses to clients, set up a DHCP server under IP -> DHCP Server.

Step 4: Apply and Test

  • Click Apply and OK to save the settings.

  • The AP is now configured and broadcasting the SSID.

3. Configuring the Station (Client)

Step 1: Access the Station Device

  1. Connect to the second MikroTik device (the station) using Winbox, WebFig, or SSH.

  2. Open the Wireless settings.

Step 2: Set Up the Wireless Interface

  1. Enable the Wireless Interface:

    • Similar to the AP, go to Interfaces and enable the wireless interface.

  2. Configure the Wireless Mode:

    • Under the Wireless tab, set the Mode to station-bridge.

    • Set the SSID to match the AP’s SSID (e.g., MikroTik-AP).

    • Set the Band and Channel Width to match the AP's settings.

    • Leave the Frequency as auto (the station will automatically connect to the AP's frequency).

  3. Security Profile:

    • Assign the same security profile used in the AP to the station's wireless interface.

    • Select the Security Profile under the Wireless tab for wlan1.

Step 3: Set Up IP Addressing

  1. Assign an IP Address:

    • Go to IP -> Addresses and assign an IP address in the same subnet as the AP (e.g., 192.168.1.2/24).

    • You can assign this IP directly to wlan1 or to a bridge interface if using one.

  2. Default Gateway:

    • Set the default gateway to the AP's IP address under IP -> Routes (e.g., 192.168.1.1).

Step 4: Apply and Test

  • Click Apply and OK to save the settings.

  • The station should now connect to the AP and establish a wireless link.

4. Testing the Wireless Link

  1. Ping Test:

    • From the station device, use the ping tool to test connectivity to the AP:

      ping 192.168.1.1

    • You should see successful ping responses if the link is working.

  2. Check Wireless Registration:

    • On the AP, go to Wireless -> Registration to see the connected station.

    • On the station, go to Wireless -> Registration to verify the connection.

  3. Throughput Test (Optional):

    • Use the built-in bandwidth test tool to measure the speed between the AP and the station.

5. Final Adjustments

  • Fine-Tuning Wireless Settings:

    • Adjust the TX Power under the Wireless tab for better signal strength.

    • Change the Frequency if there is interference on the current channel.

  • Security:

    • Ensure that WPA2 with a strong pre-shared key is used for encryption.

    • Consider using MAC Address Filtering or Access Lists to restrict connections to known devices.

Summary

By following these steps, you have successfully set up a simple wireless link between two MikroTik devices, with one acting as an Access Point (AP) and the other as a Station (Client). This setup can be used for various purposes, such as extending network coverage or connecting separate network segments wirelessly.

Keywords

MikroTik, RouterOS, RouterBOARD, wireless networking, ISP, WISP, networking equipment, routers, switches, Cloud Core Router, CCR, SXT, LTE integration, 5G, cybersecurity, network security, networking software, networking hardware, Latvia, John Trully, Arnis Riekstiņš, MikroTik Academy, MUM events, network management, hotspot, VLAN, firewall, VPN, QoS, bandwidth management, traffic shaping, wireless access point, CAPsMAN, WinBox, PoE, mesh networking, routing protocols, MPLS, OSPF, BGP, MikroTik training

میکروتیک, روتر او اس, روتر برد, شبکه بی‌سیم, آی اس پی, وایرلس آی اس پی, تجهیزات شبکه, روترها, سوییچ‌ها, کلود کور روتر, سی سی آر, اس ایکس تی, ادغام ال تی ای, 5G, امنیت سایبری, امنیت شبکه, نرم‌افزار شبکه, سخت‌افزار شبکه, لتونی, جان ترولی, آرنیس ریکسینش, آکادمی میکروتیک, رویدادهای مام, مدیریت شبکه, هات اسپات, وی‌لَن, فایروال, وی‌پی‌ان, کیو‌اُ‌اس, مدیریت پهنای باند, شکل‌دهی ترافیک, نقطه دسترسی بی‌سیم, کپزمن, وین‌باکس, پی او ای, شبکه مش, پروتکل‌های مسیریابی, ام پی ال اس, اُ اس پی اف, بی جی پی, آموزش میکروتیک

External Links

🌐 Personal Website 📄 Resume 🎥 Video Archive 💼 Finance Blog 🔐 Network & Security Notebook 🎬 Aparat Channel

Previous802.11a/b/g/n/ac ConceptsNextLink Budget Calculation

Last updated